Whirlpool Duet Dryer Will Not Start
- Check the Circuits. Always check that the dryer is receiving the proper amount of 240v current.
- Check the Door Latch. The dryer will not start if the door latch is malfunctioning.
- Check the Thermal Fuse. Inspect the thermal fuse.
- Check the Start Button.
Is there a reset button on a Whirlpool Duet dryer?
Whirlpool dryers can do many things, such as monitor moisture levels and temperature, reduce noise, periodically tumble clothes to remove wrinkles, steam clothes and adjust the overall drying time according to fabric and load size. However, one thing a Whirlpool dryer cannot do is reset itself by pushing a button.
Where is the thermal fuse on a Whirlpool Duet dryer?
Remove the back access panel on the dryer, and look for the exhaust duct near the bottom of the unit. The thermal fuse is either circular or oblong, often white plastic with black material in the center and two wire leads. The thermal fuse is mounted on the exhaust duct.
Why did my Whirlpool Duet dryer stop working?
Inspect household fuses or breakers. Replace blown fuses or reset tripped breakers. The dryer is likely using two fuses or breakers. If the dryer continues to blow fuses or trip breakers, discontinue use and call an electrician.
How do I know if the thermal fuse is blown?
Touch the left multimeter lead to the left side of the thermal fuse; touch the right multimeter lead to the right side of the fuse. Keep an eye on the multimeter needle; a needle that fails to move indicates a blown thermal fuse. If this is the case, don’t fret: thermal fuse replacement is a simple task.
When I push the start button on my dryer nothing happens?
A broken power cord, failed push-to-start switch or a bad timer can also prevent the dryer from starting. Some dryers use a motor relay to control the drive motor, so a broken motor relay can prevent the dryer from starting. In electric dryers, a blown thermal fuse can keep the dryer from starting.
How dO I know if my thermal fuse is blown?
To test if your thermal fuse has blown, touch the right side of your multimeter lead to the right side of the fuse, and repeat with the left multimeter lead. If the multimeter needle fails to move, this indicates the thermal fuse has blown.
How do I know if my thermal fuse is bad?
Multimeter Test Remove the two wire leads from the thermal fuse and touch a multitester probe to each wire terminal on the fuse. If you get a reading of infinity, the fuse is fine. Any reading less than infinity indicates a triggered thermal fuse you will need to replace.
What is a whirlpool washer duet?
The good news is Whirlpool Duet washing machines have a diagnostic mode to help troubleshoot what’s the problem with your washer. Here’s the tricky part… There have been several washing machines that Whirlpool has chosen to name Duet.
Can You reverse door on Whirlpool duet washer?
Duet dryer doors cannot be reversed for the swing. They wil only open one way. Depending on your model of washer the newers ones will allow you to reverse the door swing without a kit. The older units require a kit to reverse the washer door.
Where is the heating element on a whirlpool duet dryer?
Dryer heating element 279838-R is used on Whirlpool, Roper, Estate, Kenmore and some other brand dryers. The heating element is typically located near or attached to the bulkhead of the dryer.
How do you clean a whirlpool duet dryer?
How to Clean Whirlpool Gas Dryer Vents & Lint Traps. Remove the screws securing the round, metal vent from the back of the dryer, using a nut driver or screwdriver. Pull the vent off of the dryer vent outlet. Insert the dryer lint brush into the vent as far as it will go. Move the brush around and from side-to-side. Pull the brush out. Do this several times until there is no more lint on the brush.
